6 Series Specifications Recommended for boats 45ft and above High tech polymer housing Available in Blue,White or Green Internally serviceable Very low DC current draw No lens seals to leak No bonding to anodes required  . 12 or 24 volt DC Meets World EMI standard Current draw of less than 1.4 of an amp @ 12volts .7 of an amp @24 volts 75mm thru hull fitting A clever mix of optics 4x standard optics 12 degree 2x wide angle Eliptical optics 12 degree vertical x 50 degree horizontal Throws both a deep penertrating and  wide flat beam of light from the one unit Patented one piece thermal polymer housing with no lens seals to deteriorate and leak Complete light engine slips out from inside the vessel for maintainance or upgrade Internally driven via 2x replaceable plug-in modules  Simple 2 wire hook-up (no external drivers or ballasts) 3.7m/12ft of tinned marine cable Reverse polarity protected 3 year warranty Brillliant  White Color temperature  9000 to 10000 degrees Kelvin (the colder the white the further it travels in water) Lux output 17,700 Ultra Blue Color temperature 470nm (the color that travels further in salt water than any other) Lux output 23,220  Ultra Green Color temperature 510nm (great color in fresh water) Lux output 21,500

 

6 Gen2 Fitting Instructions

All Aqualuma lights have been tested before shipping.
It is recommended that you use a qualified boat builder to work out placement and fitting of your new underwater lights.

You will require the following to install your new Aqualuma lights.
*76mm (3”) hole saw, Wire Connectors *Fuse or Circuit Breaker
Gen 2 series housings can now be installed with any sealant approved for below water line use.

Step 1
With boat on hardstand or trailer calculate the spacings based on the width of the boat and the number of lights you want to fit. (Recommended spacing is 800mm (32 in”) for transom and 250-300mm (10 in”) below water line. Spacing for side of boat should be approximately 1.5 metres (60 in”). Mark the hole centres with a marker, be careful to check the inside of the boat for any obstacles in the area you want to drill, with that done you can now drill a small pilot hole then double check inside the boat again for anything that may obstruct the housing or retaining nut. Once you are sure you have the correct position you can now drill through the hull with the 76mm (3in”) hole saw.

Step 2
Remove the light housing from box, remove the retaining nut from the housing and clean the inside surface of the flange, clean the surface of the hull removing all antifouling from flange area and wipe clean.

Step 3
You are now ready to install the complete light fitting into the hull (there is no need to disassemble light fi tting). NB - Please see Annexe A for correct lens alignment. Apply a generous amount of sealer to the inside flange of the housing and carefully slide the housing into the hole with someone inside the boat to attach the nut, hold the housing flush with the outside surface of the boat and apply a small amount of sealer to inner surface around hole and tighten the nut by hand until tight. The nut should only be hand tight.
Caution do not fit in direct sunlight or extreme temperatures.

Step 4
Clean excess sealant from around the housing and check to make sure you have a seal all the way around the flange to the outside edge of the housing. Check the face of the housing and lens area for any sealant.

Step 5
Take the power wire and run to a known 12 or 24 volt DC fused and switchable power source with 5 amp fuse as each light uses only 1 amp @ 12 volts DC do not use higher fuse, connect the red wire to positive and the black wire to negative.

Please note Aqualuma lights are polarity sensitive.
Congratulations on purchasing and installing your new Aqualuma Underwater light you are now ready to light up the water around your boat and be the envy of your friends who have not yet seen THE LIGHT!

**Annexe A: These wide angle lights must be correctly positioned. Look through the outer lens and you will see a decal with an arrow on the primary optic holder. The arrow on the decal must be vertical, see photos**

Download printable PDF for 6 Series Fitting Instructions

Testimonials